Flex Circuit Specific Terms and Definitions

Recently, I had a few discussions with someone who was very new to flex design. I was trying to be helpful and going through several things that are specific to flex and rigid-flex design, which should be considered as you start your first design. He was listening and taking notes and suddenly stopped me and said, "You lost me a few items back; I am not completely sure I understand this terminology." This flashed me back to memories of my early days in the industry, my having also been slightly confused by the terminology. Back then, we didn’t have Google to help us out, either!  

This blog is written for those of you who are new to flex and rigid-flex and may be unfamiliar with some of the terms that get volleyed around in conversation. 

Flexible Circuit

A pattern of conductive traces bonded on a flexible substrate. There are several different substrates available, the most common being polyimide. Different than rigid materials, these laminates will have rolled annealed (RA) copper for improved flexibility. 

Rigid-Flex

This is a hybrid construction, using flex materials in areas that need to bend or flex and rigid materials in areas with dense component areas, surface mount components on both sides of the PCB, and applications with higher layer count, dense routing areas. Most common rigid materials can be incorporated into a rigid-flex construction. 

Flex Tails

Typically, it refers to the areas of flex extended out past the rigid portions of the rigid-flex. This may be one flex region or several bands of flex areas that extend in various directions. Rigid-flex is often used to solve packaging issues and connect on multiple planes. Flex tails enable this. 

Banding

Often used to accommodate a shorter flexible area if there is no room for a service loop. Instead of using the full width of the flex region between areas for each inner layer, the area can be divided into smaller bands of equal width for each inner layer, eliminating buckling and stress in that area.

Pouch

This is a protective barrier material often used in rigid-flex fabrication. Often, this is a coverlay material used to protect exposed flexible materials during processing and is removed from the flexible portion of the board before shipment. 

Coverlay

A layer of insulating material applied to the flexible circuit to insulate the conductor pattern. Coverlay is typically a layer of polyimide with acrylic adhesive. Film-based coverlay is much more flexible than cover-coat materials and is highly recommended for dynamically flexing applications or flex that will have a tight bend radius. It is important to be sure to spec enough adhesive to fully encapsulate the copper conductors. 

Cover-Coat

This is typically a photoimageable cover-coat similar to a traditional PCB solder mask but formulated to be flexible. Cover-coats are often used with lower layer count flex, applications without high flexing requirements, and in situations with tight pad features that exceed standard drilled coverlay capabilities. 

Bikini Cut

Coverlay material used to insulate the circuitry on the flexible layers is typically bonded with acrylic adhesives. It is recommended to NOT have acrylic adhesive extend more than .050" into the rigid portion of the design to avoid reliability issues in the plated through-hole areas. Bikini cut refers to cutting back the acrylic adhesive, so it is not extended into the rigid portion of the stack up. 

Gang Open

With drilled overlay, the minimum distance between features is .25 mm. If that space is not available to allow proper registration. Gang opening, opening a block of pads with one single coverlay opening is suggested. If this is not possible, common alternatives include an LPI solder mask or laser cutting of coverlay. 

Squeeze Out

As the coverlay is pressed and cured, the acrylic adhesive will "squeeze out" onto the pad area. Attention should be given to the size of the coverlay opening and pad size to factor this into annular ring calculations. 

Fillets

The gradual transition point from pad to the conductor to eliminate stress points. The pad-to-trace interface in a flex design is highly susceptible to cracking or breaking. Filleting is recommended in all flex applications.                              

Anchors/Rabbit Ears

Extra copper extended from the copper pad area and encapsulated by the coverlay to help anchor the pad to the substrate. This is recommended for all flex designs and is especially important with single-sided designs that do not have a plated through-hole to help anchor the copper. 

Bend Radius

This is the ratio of the bending radius measured to the inside of the bend to the overall thickness in that area. Typically, recommendations for non-dynamically flexing designs is 10:1 for single and double-sided construction, and 20:1 for multilayer construction. These can be exceeded but should be evaluated carefully. Dynamically flexing applications should be discussed with your fabricator for a recommended stack up.

Button Plate

Fabrication process to selectively electroplate copper to vias and onto the pads capturing the vias. The remaining copper traces do not have electrodeposited copper, increasing the flexibility of the circuit. 

I-Beam Effect

Stacking conductors on adjacent layers directly on top of one another, increasing the stiffness of the circuit in the bend or fold areas. Staggered conductors are recommended, if possible, to retain the maximum flexibility of the circuit. 

Conclusion

I hope this helps explain some of the common terminology with flex and rigid-flex materials and design. Talk to an Altium expert today to learn more or continue reading about why Altium Designer^® is the best design solution for rigid-flex PCB Design.